INDEPENDENT INDUSTRIAL INTELLIGENCEPACKAGING · ROBOTICS · PROCESSING
PackLine IQ
Packaging Automation, Robotics & Processing Technology
The PackLine Brief
END-OF-LINE / BUYER GUIDE

Beverage Full Case Inspection: Vision, Weighing or X-Ray?

Choose a method for missing bottles, wrong formats and damaged cases, then prove the reject reaches containment.

Conceptual conveyor showing an overhead camera above an open beverage crate and a shielded inspection tunnel for sealed cartons
Original PackLine IQ illustration of open-crate and sealed-carton inspection. Equipment layout is conceptual.

Start with the defect and where it occurs

Beverage full case inspection checks packed crates, trays or cartons before they reach palletizing. Use overhead vision for visible bottle positions, dynamic weighing for missing units with a reliable weight difference, and X-ray when an opaque carton hides the contents and a trial proves sufficient contrast. Set separate requirements for case count, case identity and closure condition.

Start at the crate packer discharge. A bottle can be absent, lying down or sitting too high. A closed carton can carry the right count and the wrong product. Inspect each feature where it is visible or measurable. If you inspect before closing, establish how the line keeps that result associated with the correct carton through closure and rejection. A camera checking an external barcode only verifies the code against the expected recipe. To establish that the contents match, link the case to a verified upstream product identity or inspect the contents directly.

HEUFT announced the trade fair debut of its logic II LF at BrauBeviale in Nuremberg, 10–12 November 2026. Its published configuration options illustrate how equipment suppliers match detection methods to exposed crates and closed cartons. The quoted configuration and test results determine what a machine can verify on your line.

Compare the methods on the same case formats

Full case inspection methods and the evidence to request
MethodWhere it fitsWhat to challenge
Visible-light visionOpen crates or trays with visible bottle positions. Separate views can check external codes and carton flaps.Crate ribs, cap reflections, conveyor wander, different bottle heights and incomplete views at speed.
Dynamic checkweighingClosed cases where the loss of one unit leaves a repeatable gap between complete and incomplete case weights.Light good cases, heavy incomplete cases, tare and fill variation, case spacing and belt transfers.
X-rayOpaque cases where the proposed view can resolve missing units or a defined internal position.Overlapping bottles in the beam path, corner and center positions, changes in carton orientation and the actual line speed.

Krones documents dry-section pack inspection. METTLER TOLEDO describes weight-based and X-ray completeness checks. HEUFT also lists radar as a completeness option for sealed cartons. Ask for evidence on the quoted method and test each defect independently. For imaging setup, use the machine vision inspection guide.

Workflow: Identify case recipe, then Measure the defect, then Track the case, then Confirm disposition
PackLine IQ editorial diagram · Conceptual implementation sequence; not a control or safety design.

Check whether the weight ranges overlap

Plot repeated in-motion weights for verified complete and deliberately incomplete cases of each format. Include actual variation in board, closures, bottles and fill. Compare the lowest measured good weights with the highest measured incomplete weights, then check whether the separation is large enough to accommodate normal drift and measurement uncertainty.

For example, suppose light complete cases measure 7.15 kg and heavy cases missing one bottle measure 7.20 kg. A minimum-weight threshold that accepts the 7.15 kg good case also accepts the heavier incomplete case. The example is illustrative. On a real line, use the overlapping SKU data to justify a second measurement or a pre-closure count. Use the checkweigher buyer guide to specify in-motion repeatability and transfers.

Write four acceptance checks into the purchase specification

  1. Build a defect matrix. Agree which case formats and faults each sensor must detect. For missing-unit checks, move the empty position through corners, center and every distinct row or layer relevant to the sensor view. Give each challenge case a known identity and expected outcome.
  2. Measure both error rates. Run randomized good and defective cases at agreed production rates and spacing. Record missed defects by type and position, false rejects on known good cases, and the number tested in each group. Set acceptance limits and sample sizes in advance. Zero misses in a small trial establishes the observed result for that trial.
  3. Prove physical disposition. Challenge adjacent failed cases, minimum gaps and an approved full or unavailable reject-lane condition. Check which case actually leaves the accepted flow and reconcile decisions with confirmations. Include the approved stop or hold response when disposition cannot be confirmed.
  4. Reconcile stop, restart and changeover. Exercise an approved interruption with cases between inspection and diversion. Verify how pending decisions are retained or affected cases held, how the next recipe is confirmed, and who authorizes release before the palletizer restarts.

Compare installed cost for the full duty, including spacing conveyors, reject hardware, guards and shielding where applicable, reject handling labor, integration and service. Require the supplier to quote the format changes and checks operators will repeat. The inspection supplier directory groups adjacent capabilities for RFQ planning.

Buying review areas: Worst-case SKUs, Weight overlap, Reject confirmation, Restart reconciliation
PackLine IQ editorial diagram · Application-specific buying checklist; validate requirements with qualified specialists.

Key takeaways

  • Match the sensor to the defect and the view available at that point on the line.
  • Use measured case weight ranges before relying on a weight threshold.
  • Confirm physical rejection and reconcile pending cases at restart.

Frequently asked questions

Can a checkweigher detect a missing bottle in a sealed case?

Yes, when incomplete cases remain measurably lighter than complete cases across expected packaging, fill and in-motion measurement variation. Test light complete cases and heavy incomplete cases at production speed before setting a threshold.

Can a camera count bottles inside a sealed opaque carton?

A conventional visible-light camera cannot see through an opaque carton. Inspect contents before closure, or validate a suitable downstream method such as checkweighing or X-ray. An exterior camera can still check visible flap condition and case identity.

Where should full case inspection sit on a beverage line?

Place the check after the last operation that can create the defect it is meant to find. Use a pre-closure camera when the required feature is visible only in an open case. Place the downstream reject before accepted cases can enter palletizing.

Sources & editorial method

Source-checked 12 November 2026. Uses the linked manufacturer announcements and public technical documentation. The supplier examples describe available configurations. The trial design is PackLine IQ editorial analysis.

Suggest a correction

PackLine IQ editorial desk

Reviewed and source-checked by the PackLine IQ editorial desk.

Editorial standards
RELATED INSIGHT

Continue the topic

Plan view comparing a beverage crate packer with opposite-end conveyor connections and one with parallel conveyors returning to the same end
End-of-Line

Beverage Crate Packers: Straight-Through vs. Same-End Layouts

Compare conveyor routes, bottle and crate compatibility, and accepted crates per hour before specifying a returnable-bottle packer.

6 min read · Technical guide
Vision camera monitoring containers on a stainless packaging line
AI & Machine Vision

Machine Vision for Packaging Inspection: Detecting Defects at Production Speed

How lighting, image acquisition and validated decisions work together on a packaging line.

12 min read · Technical guide
Conceptual stainless combination inspection conveyor with metal detector tunnel, weighing belt and reject bin
Packaging Machinery

Checkweigher and Metal Detector Combination: Selection, Reject Handling and Buyer Tests

Compare integrated and separate inspection machines, then test weighing, metal detection and the physical reject path as distinct duties.

19 min read · Technical guide